| 00:15 | dv_ | jnettlet: oh nice |
| 00:23 | _rmk_ | void__: you're following the instructions about pressing the little button while turning on? |
| 00:23 | _rmk_ | robclark: its the same as the raspberry pi, and note that it's strictly 3.3v only |
| 00:42 | void__ | _rmk_ yep well i followd them already ... i already created an post describing my situation at solid run forums |
| 00:42 | void__ | viewtopic.php?f=7&t=1495 |
| 00:42 | void__ | well yes the last thing that im on now is, the cubox wont accept any .bin file send to it |
| 00:43 | void__ | blocks dont match or something |
| 00:47 | _rmk_ | what does stty -aF /dev/ttyUSB0 say? |
| 00:50 | void__ | well that tells a lot here just usb connected no power supply @ cubox |
| 00:50 | _rmk_ | it should tell a lot :) |
| 00:50 | void__ | well with power at cubox nothing changes |
| 00:50 | void__ | ok well thats good news :) |
| 00:51 | _rmk_ | it won't change with/without power |
| 00:51 | void__ | i see |
| 00:51 | _rmk_ | its asking what the current settings for ttyUSB0 are on your computer |
| 00:51 | _rmk_ | please check that it says "speed 115200 baud" |
| 00:51 | void__ | speed is ok 115200 |
| 00:52 | void__ | baud yes |
| 00:52 | _rmk_ | 3 lines below: -parenb -parodd cs8 |
| 00:52 | void__ | yep all of them |
| 00:52 | void__ | cs8 hupl |
| 00:53 | _rmk_ | ok, good. |
| 00:53 | _rmk_ | just to make sure nothing silly is happening: also do this: stty -F /dev/ttyUSB0 raw |
| 00:54 | _rmk_ | after that, then do: sx -vv u-boot-cubox_hynix_cubox_1GB_uart.bin < /dev/ttyUSB0 > /dev/ttyUSB0 |
| 00:55 | _rmk_ | and plug the power in while holding the little button down |
| 00:57 | void__ | ok did all that, but still same problem occurs |
| 00:57 | void__ | Wiederholungsversuch 0: Sektor nicht bestÃĪtigt |
| 00:57 | void__ | sector not verified or something |
| 00:58 | void__ | but well im sure i have v2 and the 1gb version |
| 00:58 | _rmk_ | you should get it in English if you prefix the "sx" command with LANG=C :) |
| 00:59 | _rmk_ | ok. when you press that little button, can you feel it "click" ? |
| 01:00 | void__ | yep it clicks and well it already worked before but since i something of interrupted the last boot after flashing the bin this error occurs all the time |
| 01:00 | void__ | btw how do i prefix commands ? |
| 01:01 | _rmk_ | LANG=C sx -vv u-boot-cubox_hynix_cubox_1GB_uart.bin < /dev/ttyUSB0 > /dev/ttyUSB0 |
| 01:01 | robclark | _rmk_, yeah, r-pi is one thing I don't have.. I was hoping it would be same as arduino or beaglebone-black.. |
| 01:01 | void__ | ok thats easy :) thanks |
| 01:02 | robclark | and my ifc6410 is yet again something different and custom |
| 01:02 | robclar | 01:02 * robclark just picked up some jumper wires.. problem solved |
| 01:03 | _rmk_ | yea, I had some wires with pin sockets I'd soldered on to them (rather than crimping) so I just re-used those and soldered them to other wires I had :) |
| 01:03 | _rmk_ | keep meaning to make up a proper cable or something |
| 01:03 | void__ | well i get now |
| 01:03 | void__ | Xmodem sectors/kbytes sent: 0/ 0kRetry 0: NAK on sector |
| 01:03 | void__ | Retry 0: NAK on sector |
| 01:03 | void__ | repeats |
| 01:05 | _rmk_ | hmm. |
| 01:07 | robclark | had to pick up an extra u-sd card too.. it's nice having a microcenter in walking distance :-) |
| 01:08 | void__ | where does the bin file for uart gets written ? |
| 01:08 | void__ | is this a replaceable part if its dead ? |
| 01:09 | void__ | i go my first cubox today ^^ |
| 01:12 | _rmk_ | what if you do: md5sum u-boot-cubox_hynix_cubox_1GB_uart.bin |
| 01:13 | ezequielgarcia | Turl: hello |
| 01:13 | Turl | hey ezequielgarcia |
| 01:14 | _rmk_ | it should come out with: "552b15a996ea470753d72b5332c01abd u-boot-cubox_hynix_cubox_1GB_uart.bin" |
| 01:14 | void__ | same as http://download.solid-run.com/pub/solidrun/cubox/u-boot/2009.08_5.4.4_SR1/aug-6-2013/ |
| 01:14 | void__ | 6b19fbc89b1a8ac452980c9f798eeab1 u-boot-cubox_hynix_cubox_1GB_uart.bin |
| 01:15 | void__ | thanks for any help so far guys |
| 01:17 | _rmk_ | hmm. what about: ls /dev/ttyUSB* |
| 01:18 | void__ | well nothing just /dev/ttyUSB0 as expected# |
| 01:20 | _rmk_ | I can't think of anything else to check at the moment |
| 01:21 | void__ | well thanks though |
| 01:21 | _rmk_ | you may try again tomorrow - earlier if you can when there may be more people around. |
| 16:04 | rabeeh | void__: ping |
| 16:40 | _rmk | 16:40 * _rmk_ mods his rpi case for the c1 - needs more than jnettlet's did - there's a post which fouls the regulator |
| 16:40 | jnettlet | _rmk_, oh those posts in the bottom? |
| 16:41 | _rmk_ | yep |
| 16:41 | jnettlet | yeah I forgot I clipped those out. |
| 16:41 | jnettlet | sorry |
| 16:41 | jnettle | 16:41 * jnettlet should have photo documented it |
| 16:46 | jnettlet | I just clipped those out with a pair of carpenters pincers. So quick I didn't even think about it. |
| 16:47 | jnettlet | I guess the RPi has holes in the board that fit around those. |
| 17:16 | _rmk_ | hdmi connector also seems to be slight off too |
| 17:16 | rabeeh | _rmk_: have a picture for the regulator? |
| 17:16 | rabeeh | hdmi is ok on my side |
| 17:17 | rabeeh | the two issues i have today is rj45 should be 1.5mm to the inner side of the board; and the dual usb |
| 17:18 | _rmk_ | rj45 is absolutely fine for me |
| 17:18 | _rmk_ | the corner of the DPAK regulator is right where one of the board support posts are in this case |
| 17:18 | rabeeh | can you take a picture? |
| 17:18 | _rmk_ | and as you look into the hdmi, it's about 1mm too close to the left |
| 17:19 | _rmk_ | yep, in a mo |
| 17:24 | _rmk_ | http://www.home.arm.linux.org.uk/~rmk/cubox/IMG_1527.JPG |
| 17:24 | _rmk_ | http://www.home.arm.linux.org.uk/~rmk/cubox/IMG_1528.JPG |
| 17:24 | _rmk_ | that one you can see the position of the ether and usb |
| 17:24 | _rmk_ | http://www.home.arm.linux.org.uk/~rmk/cubox/IMG_1529.JPG |
| 17:24 | _rmk_ | those fit perfectly |
| 17:25 | _rmk_ | http://www.home.arm.linux.org.uk/~rmk/cubox/IMG_1530.JPG |
| 17:25 | _rmk_ | again, that's fine |
| 17:25 | _rmk_ | http://www.home.arm.linux.org.uk/~rmk/cubox/IMG_1531.JPG |
| 17:25 | _rmk_ | that shows the post which causes problems with the DPAK regulator |
| 17:32 | _rmk_ | LED light pipes don't line up either |
| 17:32 | _rmk_ | centres of the LEDs need to be where the T is on ACT |
| 17:46 | _rmk_ | that's better, helps to plug the SD card back in for it to boot :) |
| 17:50 | _rmk_ | http://www.home.arm.linux.org.uk/~rmk/cubox/IMG_1532.JPG - LEDs position |
| 17:55 | rabeeh | 5 LEDs |
| 17:55 | rabeeh | i think three can be managed |
| 17:56 | rabeeh | the link and activity can be combined into a single led |
| 17:57 | rabeeh | for the speed the board supports 10/100 or 10/100/1000 |
| 17:57 | rabeeh | so i'm not sure you can fit one LED to indicate which speed it is |
| 17:58 | rabeeh | _rmk_: what is this background paper you have? |
| 18:01 | jnettlet | oh that works much better. much easier to illustrate the problems with the translucent case. |
| 18:07 | _rmk_ | rabeeh: a CAA frequency card - lists the frequencies for various aerodromes in the UK :) |
| 18:08 | jnettlet | _rmk_, does the IR receiver work through the case? |
| 18:09 | _rmk_ | I'll test in a moment |
| 18:10 | _rmk_ | well... it does seem to |
| 18:10 | _rmk | 18:10 * _rmk_ grumbles |
| 18:10 | _rmk_ | g+ fail |
| 18:11 | _rmk_ | "Your post was not shared. Please try again." |
| 18:11 | jnettlet | never seen that. I guess the NSA scanner must be bogged down. |
| 18:12 | _rmk_ | must be |
| 18:13 | _rmk_ | remember, that's the only part of the american government that listens :) |
| 18:13 | _rmk | 18:13 * _rmk_ adds the photos to an album first |
| 18:15 | _rmk_ | that worked |
| 18:16 | dv_ | well great. I saw a nasty race condition with the VPU happening about two days ago, and now it doesnt ever happen again |
| 18:21 | _rmk_ | It's sitting on top of my N2100, which is powering the carrier-1 |
| 18:25 | jnettlet | I actually use a Verbatim Mediashare for my NAS. Nice little box actually. Marvell SOC inside. |
| 18:35 | _rmk_ | jnettlet: yes, I think the N2100 suffers a bit in terms of internal bus bandwidth(s) |
| 18:39 | jnettlet | the Mediashare also comes in a nice aluminum case. When everyone was going nuts over the pogoplug I was surprised it didn't get more fanfare. |
| 18:39 | jnettlet | for just a little more money you got what I thought was a much nicer platform |
| 18:44 | jnettle | 18:44 * jnettlet is secretly hoping that he can use a Cubox-i or Carrier One board to upgrade it. |